
Creasol UniRecl Multifrequency ICH receiver Usable with almost any remote control, AM and FM, fixed and rolling code Creasol UniRecl Multifrequency universal receiver with 1 opto-insulated output. Receives in 1 or 2 frequencies, selectable by the user, AM/FM: 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8 MHz, 288-418MHz, AM/FM. Smart Home Solutions http://www.creasol.it ENGLISH Introduction: this device, very compact and easy to be installed, has a solid-state relay output which permits to control any electronic board with a low-voltage input, by almost any remote control in the market transmitting in the range 433.42-868.8 MHz with AM or FM modulation and with a good frequency stability (using crystal or SAW resonators). Installation: this device has 5 wires, one of which is used as antenna and should not be connected anywhere. Two wires, marked as Supply, should be connected to the power supply 7-36Vdc or 7-27Vac. Two wires, marked as Sw1+ and Sw1-, should be connected to the input of the electronic board to be controlled, where it's connected the external switch start button, as shown in Fig. 1. 1. Check voltage on start button: it should be in the range 2-40V. 2. Measure the current through the start button: it should be less than 50mA. 3. Connect wires marked as Supply to the power supply: don't care about polarity. 4. Connect wires Sw1+ and Sw1- to the electronic board inputs, respecting polarity. 5. Configure the device (frequency, modulation, output type, ...) if needed. 6. Learn one or more remote controls, following the instructions below. It's also possible to use Sw wires to supply an external 5-24V relay coil, with a protection diode. Do not connect wires to a power supply source! Configuration: this device is supplied pre-configured to receive at 433.92 MHz, AM, and to activate the output for 500ms. To modify this configuration, press quickly the button Prog a number of times corresponding to the parameter to modify: Led will flash to notify the current value of that parameter. Then, press again button Prog for the number of times corresponding to the desired value, as specified in the table. If programming fails, a long red flash will be emitted. Learning remote controls: press the Prog button twice to enable learning mode: Led starts flashing slowly. Within 10s, press the button on the remote controls that should be learned. Every time a new code is learned, the 10s timeout is reload: Led flashes twice if the code is learned, 3 times if was already learned, 6 times if memory is full. Removing remote controls: press the Prog button 3 times, then press button on remote controls in the same way as learning procedure. Led flashes 4 times for any removed code. To blank the whole memory, press the Prog button 10 times, wait for Led flashing, then press Prog button 3 times; press 4 instead of 3 to do a factory reset. Learning master remote controls: press the Prog button 4 times, then press button on remote control: this remote controls will not activate the output, but can be used to enable learning procedure without the need to access the receiver. To learn new remote controls in this way, put the master remote control in trasmission for 2s, then keep in transmission for 2s the new remote controls that should be learned: every time a new remote control is learned, the 10s timer is reload to permit successive learnings. Security and safety: do not use in systems that require a high level of anti-theft security. Installation should be done by a qualified technician, in a well insulated enclosure, protected by dust, humidity, steam and contact with other circuits and metal parts. All responsibility, for any damage caused by not complying with the instructions in this manual, is declined. Warranty: the warranty complies with statutory requirements, and cover only defects, within the product itself, in material and manufacture. Your local stockist should be contacted in connection with any warranty-related matters. Creasol hereby declares that this receiver UniRec1 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Declaration of Conformity can be obtained from http://www.ce.creasol.it Einleitung: Dieses Gerät ist sehr kompakt und einfach zu installieren. Mit einen Spannungsausgang wird die Motorsteuerung am Niederspannungseingang angesteuert, Funkhandsender im Frequenzbereich von 433.42 bis 868.8MHz, AM oder FM- in rolling oder DIP-Schalter- Codierung können eingelernt werden. Installation: Dieser Empfänger hat 5 Kabel. Eines wird als Antenne benötigt und sollte nirgends angeschlossen werden. 2 Kabel, welche als Supply markiert sind, werden an das Netzteil 7-36Vdc oder 7-27Vac angeschlossen. Die beiden Kabel, welche als Sw1* markiert sind, werden an den Eingang der Steuerung (ab jetzt als Start Button bezeichnet) angeschlossen (wie in Abbildung 1 beschrieben). 1. Spannung am Start Button überprüfen: Dieser sollte zwischen 2-40V sein. 2. Den Durchgangsstrom vom Start Button messen: Er sollte weniger als 50mA. 3. Die als Supply Kabel mit dem Netzteil verbinden: Polung spielt keine Rolle. 4. Schließen Sie die Kabel von Sw1 * an die Eingänge der Elektronikplatine an. 5. Den Empfänger entsprechend: Frequenz, Modulation, Typ des Ausgangs, ... 6. Eine oder mehr Fernbedienungen gemäß Anleitung einlernen. Es ist auch möglich, Switch kabel zur Versorgung einer externen 5-24V-Relaisspule mit einer Schutzdiode zu verwenden. Schließen Sie die Schalterkabel nicht an eine Stromquelle an! Konfiguration: Der Empfänger ist vorkonfiguriert mit der Frequenz von 433.92 MHz AM und einer Einschaltzeit von 500ms. Um diese Konfiguration zu ändern, den Prog Knopf schnell drücken: Die LED-Anzeige leuchtet um die aktuelle Einstellung anzuzeigen. Den Prog Knopf so viel mal drücken, bis der gewünschte Parameter angezeigt wird (sieh Tabelle). Wenn die Programmierung fehlgeschlagen ist, leuchtet die LED-Anzeige lang auf. Sendr anlernen: Drücken Sie die Prog 2 mal, um den Lernmodus zu aktivieren: Led blinkt langsam. Drücken Sie eine Taste auf der Sender, die innerhalb von 10s gelernt werden sollte: Led blinkt zweimal, wenn der Code ist so programmiert, 3-mal, wenn bereits gelernt wurde, 6-mal, wenn der Speicher voll ist, dann ist es möglich, andere Fernbedienungen innerhalb von 10s zu lernen. Entfernen von Sender: Drücken Sie die Prog-Taste 3-mal, und drücken Sie Taste auf Sender, die entfernt werden sollen. Led blinkt 4-mal für jeden entfernten Code auf. Um Leer den gesamten Speicher, drücken Sie die Prog 10mal,abwarten Led zu blinken, dann Prog 3-mal drücken; Presse 4 statt 3 einen Werksreset zu bekommen. Lernen Master Sender: Drücken Sie die Prog 4-mal, und drücken Sie Taste auf der Sender: Die Sender wird der Ausgang nicht aktiviert, kann aber verwendet werden, Lernverfahren, ohne dass der Empfänger den Zugang zu ermöglichen. Sicherheit: Verwenden Sie in nicht-Systeme, die ein hohes Maß an Anti-DiebstahlSicherheit erfordern. Die Installation sollte von einem qualifizierten Techniker durchgeführt werden, in einem gut isolierten Gehäuse, durch Staub, hoher Luftfeuchtigkeit, Dämpfen und Kontakt mit anderen Schaltungen und Metallteilen geschützt. Alle Verantwortung für Schäden, die nicht mit den Anweisungen in diesem Handbuch Einhaltung verursacht wird, zurückgegangen. Garantie: erfüllt die gesetzlichen Anforderungen und decken nur Defekte im Produkt selbst, in Material und Herstellung. Ihr Fachhändler sollte im Zusammenhang mit Gewährleistungsfragen kontaktiert werden. CE-Konformitätserklärung: Creasol erklärt hiermit, dass der Empfänger UniRec1 entspricht den grundlegenden Anforderungen der europäischen Richtlinie 2014/53/EU. Konformitätserklärung ist http://www.ce.crea
Katalog auf Seite 1 öffnen2 Seiten
1 Seite
2 Seiten
22 Seiten