SFS01 EvaKit Brochure de
1 / 7Seiten

Katalogauszüge

SFS01 EvaKit Brochure de - 1

Thermischer Strömungssensor Optimal für die Demonstration und Evaluation des SFS01 (Silicon Flow Sensor) Eigenschaften & Anwendungsbereiche Anwendungen Analoge und digitale (I2C) Anschlüsse Anwendungen in batteriebetriebenen / portablen Geräten Veranschaulichung und Dimensionen (in mm) des SFS-Chips 1) Genaue Grösse unter Abmessungen zu finden

Katalog auf Seite 1 öffnen
SFS01 EvaKit Brochure de - 2

Pneumatische Anschlüsse: Bis zu 1 bar (einseitig auf Membran über 10 Jahre) Ausgangsspannung: Digitaler Anschluss: Digitales Signal: 3.3 V I2C (Pull-up Widerstände on-board) Kalibriertes Signal (bis ±200 sccm) Rohwertsignal (digits) < 1 mA Analoge Ausgangslast: Integrierter Sensor: Die nachfolgenden Werte gelten als typisch und sind unter Laborbedingungen erreicht worden, wobei das verwendete Gas Stickstoff war. Medium: nicht aggressive Gase (5-95 % rel. Feuchte, nicht kondensierend)

Katalog auf Seite 2 öffnen
SFS01 EvaKit Brochure de - 3

For integration with a micro-controller, the SFS Demo Board has an I2C-compatible interface which supports both 100 kHz and 400 kHz bit rates. The default I2C slave address is programmed on 0x28 and can be adjusted in the entire 7-bit address range (0x00 to 0x7F). Parameter Hold time (repeated) START Setup time for a repeated START Data hold time Data setup time Setup time for STOP Pulse duration of spikes suppressed by input 50 filter

Katalog auf Seite 3 öffnen
SFS01 EvaKit Brochure de - 4

Reading the data form SFS Demo Board During normal operation the SFS Demo Board is ready to transmit current calibrated and raw flow’s value. The typical transmission is: higher bite lower bite higher bite lower bite Calibrated flow The calibrated flow read from the module is in signed fixed-point integer Q6 format. To convert it to decimal format, the read value has to be divided by 26 = 64. The minimum value is -512, the maximum value is 511.98438. The resolution of each value is 1/26 = 0.015625. The raw value read from the module is in unsigned integer format. Entering the Command Mode...

Katalog auf Seite 4 öffnen
SFS01 EvaKit Brochure de - 5

Reading parameters from the module After successful read instruction the module fills the I²C buffer with the selected parameter. All parameters read from the module, except I²C_address, Serial Number and Firmware Revision, are in signed fixed-point long IQ22 format (4 bytes). To convert them to decimal format the read value has to be divided by 222 = 4 194 304. The minimum value is -512, the maximum value is 511.999 999 762. The resolution of each parameter is 1/222 = 0.000 000 238. I²C_address, Serial Number and Firmware Revision parameters are read in unsigned long format. Additionally,...

Katalog auf Seite 5 öffnen
SFS01 EvaKit Brochure de - 6

Reboot After receiving this command, the module reboots. Typical parameter’s read sequence To read parameter(s) form the flash memory please follow steps: Write 0xA0 to the module – start the command mode Wait 1 ms Write 0x00…0x07 to the module – an address of the parameter Wait 1 ms Read 4 bytes from the module If needed repeat steps 3-5 for another parameter Write 0xA1 to the module – exit command mode Typical parameter’s write sequence To write parameter(s) to the flash memory please follow steps: Write 0xA0 to the module – start the command mode Wait 1 ms Write 0x20…0x25 to the module –...

Katalog auf Seite 6 öffnen
SFS01 EvaKit Brochure de - 7

Bestellinformation Modul Ehemalige Bestellnummer Zusätzliche Dokumente Application Note Innovative Sensor Technology IST AG, Stegrütistrasse 14, 9642 Ebnat-Kappel, Schweiz Tel.: +41 71 992 01 00 | Fax: +41 71 992 01 99 | Email: info@ist-ag.com | www.ist-ag.com Alle mechanischen Abmessungen gelten bei 25 °C Umgebungstemperatur, falls nicht anders angegeben • Alle Daten ausser die mechanischen Abmessungen dienen nur Informationszwecken und sind nicht als zugesicherte Eigenschaften aufzufassen • Technische Änderungen ohne vorherige Ankündigung sowie Irrtümer vorbehalten • Die Informationen auf...

Katalog auf Seite 7 öffnen

Alle Kataloge und technischen Broschüren von Innovative Sensor Technology IST AG