MagSprings > ֯è , unlike mechanical springs, deliver a constant force over their entire wide working rang. MagSpring >  consists of only two rugged components: a stator and a slider. MagSprings >  are totally passive,. Their operation is based entirely on a unique (patent pending) application of permanent magnets no electricity at all. >

MagSprings > are used to provide either an assisting or a resisting constant force. In vertical applications particularly , MagSprings > Working stroke If the MagSpring are used to compensate for the weight of payloads being raised, thus allowing the use of smaller motors. In horizontal applications, MagSprings > is unloaded the slider is about in the middle of the stator. Thereby the called working end of the slider sticks a little bit more out of the stator than the other end of the slider. (Note that a payload can be fixed on both ends of the slider). Starting from this unbend position the...

Figure 5 shows a MS01-20 MagSprin >  assembled in parallel to a linear motor. The equipment shown applies soldering paste through a fine needle. In case of power loss or shut down the MagSpring >  moves the needle up and out of the way making sure that there is no damage to the needle. Fig 3 MagSpring >  MS01-37 assembled to a H01-37-Guidance of LinMot >  . Figure 4 shows a vertical application of a LinMot >  Linear Motor with a H01-37-Guidance system together with a MagSprin >  g. The MagSpring >  pushes up with a constant force of up to 60 N. The MagSpring >  over compensates the earth's...

Slider End with serial number Stator Part-Nr Length L > Stator Diameter Mass MS01-20x60 0250-2200 60 mm [+/-0.1] (2,36 in) 20 mm (7.87 in) 75 g (0.16 lb) MS01-20x140 0250-2201 140 mm [+/-0.1] (5.51 in) 20 mm (7.87 in) 180 g (0.39 lb) MS01-20x220 0250-2202 220 mm [+/-0.15] (8.66 in) 20 mm (7.87 in) 285 g (0.62 lb) > Materials: Stator casing: Steel with Ni plating bearing: based on POM (Delrin) Slider End with serial number Stator Part-Nr Length L > Stator Diameter Mass MS01-37x80 0250-2203 80 mm [+/-0.2] (3.15 in) 37 mm (1.46 in) 440 g (0.91lb) MS01-37x155 0250-2204 155 mm [+/-0.2] (6.10 in) 37...

Mounting flange for MagSpring >  MS01-20 Stator > All Dimensions in mm / (inch) Material: Aluminium (AlMgSi), black anodized Mass: ca 30 g (0.066 lb) Description: MF01-20/H23 Part-No : 0250-2306 Adapter between MagSpring >  MS01-20 Stator and H01-23-Guidance > All Dimensions in mm / (inch) Description: Aluminium (AlMgSi), black anodized Mass: ca 18 g (0.04 lb) Bezeichnung: MA01-20/H23 Part-No : 0250-0116 >

Mounting flange for MagSpring >  MS01-37 Stator > All Dimensions in mm / (inch) Material: Aluminium (AlMgSi), black anodized Mass: ca 70 g (0.015 lb) Description: MF01-37/H37 Part-No : 0250-2307 Adapter between MagSpring >  MS01-37 Stator and H01-37-/ H01-48-Guidance > All Dimensions in mm / (inch) Material: Aluminium (AlMgSi), black anodized Material: Aluminium (AlMgSi), black anodized Mass: ca 18 g (0.04 lb) Mass: ca 32 g (0.071 lb) Description: MA01-37/H37 Description: MA01-37/H48 Part-No : 0250-0117 Part-No : 0250-0118 >

Specification of products are subject to change without notification. MagSpring  is a registered Trademark of NTI AG. (V3.1) MagSpring >  products are available from more than 80 Distributors worldwide. Contact Europe/Asia NTI AG MagSpring Tel. +41 (0)56 419 91 91 Haerdlistrasse 15 Fax. +41 (0)56 419 91 92 CH-8957 Spreitenbach Email: [email protected] Switzerland Web: www.MagSpring.com Contact North America LinMot Inc . N2444 Broad Street Phone +1-877-546-3270 or 262-728-2699 Delavan Fax: +1-800-463-8708 or 262-740-0141 WI 53115 Email: [email protected] USA Web: www.MagSpring.com >